Showroom: 16728 E Smoky Hill Rd, Unit 10-A, Centennial, CO 80015Mon–Fri 10 AM–6 PM · Sat by appointment · (303) 993-6479

Hardwood Floor Refinishing in Centennial & Denver Metro

Local fact: according to U.S. Census data, two out of three homes in Centennial and Littleton were built before 1980. Many homes that age have original hardwood that can be sanded and refinished instead of replaced. More on our Denver-area flooring facts page.

Scratched, worn or dated hardwood does not always need to be replaced. Solid hardwood and many engineered floors can be sanded and refinished to look close to new, often with a new stain color. Floor & More refinishes hardwood floors in Centennial and across the Denver Metro.

Before and after comparison of a hardwood staircase refinish
Before and after comparison of a hardwood staircase refinish

Refinishing services

  • Full sand and refinish: sanding to bare wood, optional stain, and new protective coats.
  • Stain color changes: move from orange or yellow tones to modern naturals, grays or darker browns.
  • Screen and recoat: a lighter buff and fresh topcoat for floors with surface wear but no deep scratches.
  • Board repair and replacement: replace damaged or stained boards and blend them in before finishing.
  • Stair treads and landings to match the main floor.

Refinish or replace?

Refinishing usually makes sense when the floor is solid hardwood or a thick-wear-layer engineered floor, the boards are tight and flat, and the damage is mostly surface scratches, dull finish or color you no longer like. Replacement makes more sense when boards are cupped, water-damaged in large areas, or the engineered wear layer is too thin to sand. If replacement is the better call, we will tell you and walk you through hardwood installation options.

Signs your floors are ready

  • The finish looks dull or gray in walkways and in front of the sink, even right after cleaning.
  • Water no longer beads on the surface and soaks in or darkens the wood.
  • Scratches from pets, chairs or grit have worn through the finish.
  • The color has gone orange or yellow, which is common with older oil-based finishes.
  • You’re getting the house ready to sell, or you’re putting in new floors next to old ones and want them to match.

If only the topcoat is worn and the wood itself looks fine, a screen and recoat may be all you need. If the damage reaches the bare wood or you want a different color, it takes a full sand and refinish.

The finish matters

On recent jobs we’ve used two-component water-based finishes such as Pallmann X96. They dry clear instead of ambering, smell far less than oil-based polyurethane and hold up well in busy kitchens and hallways. Some homeowners still prefer the warmer look of an oil-based finish, and that’s a fine choice too. We’ll show you the difference on a sample before you decide, along with sheen options from matte to semi-gloss.

Refinishing stairs

Stairs take the most wear of any wood in the house, and they’re often the first thing people notice when they walk in. Most of the photos on this page are staircases. We sand treads by hand and with edgers, stain them to match the floor or go darker for contrast, and can paint the risers white for a cleaner look. If the treads are carpet-covered or too far gone, we can replace them with new hardwood treads. See our stair flooring page for those options.

Dark walnut stained hardwood stair treads, professionally refinished
Dark walnut stained hardwood stair treads, professionally refinished

What to expect

Assessment

We check the species, wear layer, existing finish and any damaged areas, and test a stain sample if you are changing color.

Prep and sanding

Furniture needs to be moved out. We sand in stages to remove the old finish and scratches.

Stain and finish

Stain is applied if you chose one, followed by protective coats with drying time in between.

Cure time

Light foot traffic can usually resume before furniture and rugs go back. We give you specific timing for the finish used.

Caring for refinished floors in Colorado

Low humidity on the Front Range makes wood shrink in winter. A humidifier, felt pads under furniture and a pH-neutral cleaner go a long way. Read our hardwood care guide for Colorado for more.

Service area

We refinish floors throughout the Denver Metro, including Centennial, Aurora, Parker, Greenwood Village, Highlands Ranch, Lone Tree, Littleton and Denver.

Recent work

See more on our projects page and full gallery.

Why homeowners choose Floor & More

  • One local team: our showroom is in Centennial, and the same people who help you choose materials coordinate the installation.
  • Materials you can see first: tile, flooring and cabinet samples at the showroom, or brought to your home.
  • Written quotes: a clear list of what is included before any work starts.
  • Flooring and remodeling under one roof: so refinishing and the floors around it are planned together.
  • Past work: browse our project gallery and recent projects.

Example project: hardwood refinishing in Littleton with a custom stain, two coats of Pallmann X96 satin and new flush-mount vents.

Helpful guides

Hardwood refinishing FAQ

Can engineered hardwood be refinished?

Often, yes, if the wear layer is thick enough. We check this before quoting.

Can you change the color of my floors?

Yes. Sanding to bare wood lets us apply a new stain. We test samples first so you can see the color on your actual floor.

Do I need to leave the house?

For the finish coats it is usually best to stay off the floors and keep the area ventilated. We will explain what to plan for.

How often should floors be refinished?

It depends on traffic, pets and care. Many homes only need a screen and recoat between full refinishes.

How long does hardwood floor refinishing take?

It depends on the size of the area, whether you’re changing the stain color, and the number of coats. A screen and recoat can be quick. A full sand and refinish with stain takes several days with drying time between coats. We’ll give you a day-by-day plan before we start.

Is refinishing dusty?

Sanding does make dust. Before we start we’ll talk about which rooms to close off and what to cover so the rest of the house stays as clean as possible.

Can you refinish just one room?

Yes, but stain color and sheen can look slightly different from the rooms next to it. Where the floor runs continuously from room to room, it often looks better to refinish the whole run and end at a doorway or threshold.

Can pet stains be sanded out?

Light surface stains often sand out. Dark stains that have soaked deep into the wood usually don’t, and the best fix is to replace those boards before refinishing. We’ll point them out during the assessment.

What about the gaps between my boards?

Small gaps that open in winter and close in summer are normal in Colorado’s dry climate, and filling them often leads to filler that cracks out. Larger permanent gaps or loose boards can be repaired as part of the job.

Ready to talk about your hardwood floors? Request a free estimate or call (303) 993-6479. Our showroom at 16728 E Smoky Hill Rd, Unit 10-A, Centennial is open Monday through Friday, 10 AM to 6 PM, and Saturday by appointment.

Get Started

Request a Free Estimate

Tell us what you’re planning and we’ll get back to you. Free, no obligation, and we price materials, labor and subfloor prep up front.

This field is required.
This field is required.
Project type
Scope
Budget range
Timeline
This field is required.

Or call 303-993-6479 · showroom at 16728 E Smoky Hill Rd, Unit 10-A, Centennial